PowerPro 205SI

200 amp TIG welder with stick and plasma capability
Special Price $1,633.05 Regular Price $1,719.00
In stock
Looking for a good all around welder with some extra features?  The  PowerPRO 205Si from Everlast is designed to be just that unit.  With 200 amp TIG, 160 amp  Stick and 50 amp Plasma cutter capabilities, the digitally controlled IGBT Inverter welder/cutter is an all-in-one solution that is useful in many situations where space and portability are key concerns.  The flexibility and versatility that the multi-process PowerPro 205S offers is hard to beat. Stable arc performance helps both hobbyists and professionals to make quality repairs in the field or in the fab shop.   The TIG pulse capability further extends the unit's capabilites, as well as the fully adjustable AC Frequency and AC balance which improves aluminum welding capabilities.  The PowerPRO 205Si multi-unit is definitely the utility player in Everlast's lineup and is ready to go to work anywhere it is needed.
Write Your Own Review
You're reviewing:PowerPro 205SI
All-in-one portability
Compact IGBT Inverter design and low power consumption is ideal for portable use
Compact, yet powerful TIG welding/Plasma cutting features
Easy to use controls with simple selector switch for process changeover
Quick change out of torches for easy change from TIG to plasma back to TIG
Good duty cycle ratings for TIG, Stick, and Plasma
Duty Cycle indicator warns when thermal threshold has been exceeded and interrupts welding/cutting output until condition is resolved
Over Current indicator warns when duty cycle has been exceeded and interrupts welding/cutting output until condition is resolved
OK to cut indicator lights up when air pressure meets minimum required operating pressure and interrupts cutting output when air pressure is too low
Low dross cuts on steel up to 5/8" with up to 3/4" maximum capacity (under ideal conditions)
Exceptional arc stability for TIG/Stick functions
15ft. Everlast 26-Series air-cooled TIG torch with DINSE-style 35 series connector
Stick electrode holder with 10 ft cable and DINSE-style 35 series connector
14ft. Everlast PT-60 Plasma torch with DINSE-style 35 series connector
Work clamp with 10 ft. cable and DINSE-style 35 series connector
Foot pedal
Argon regulator for TIG
Air Pressure regulator with water trap/filter (Note: This is not an air dryer. A separate, inline air dryer, supplied by the customer should be installed)
Consumable starter kit for TIG and Plasma (Does not include TIG tungsten)
IGBT Inverter Type:
220/240 V 1 Phase
TIG output type:
TIG Start Type:
High Frequency Only
Yes, Adjustable
Plasma Cutter Arc Start Type:
Blow Back (Piston type)
OK-to-Cut Indicator/Low Air pressure safety:
AC Frequency:
AC Balance (cleaning):
85V TIG/Stick, 250V Plasma
Max Inrush ( I1MAX ) Amps:
Maximum Rated (I1EFF ) Input Amps:
TIG Output Amps/Volts @ Rated Duty Cycle:
200A/18V @ 60% Duty Cycle
160A/16.4V @ 100% Duty Cycle

Stick Output Amps/Volts @ Rated Duty Cycle:
160A/26.4V @ 35% Duty Cycle
130A/25.2V @ 60% Duty Cycle
100A/ 24V @ 100% Duty Cycle
Plasma Output Amps/Volts @ Rated Duty Cycle:
50A/100V @ 35% Duty Cycle
40A/96V @ 60% Duty Cycle
30A/92V @ 100% Duty Cycle
TIG AC Amp/Volt Range:
20A-200A; 10.8V-18V
TIG DC Amp/Volt Range:
5A-200A; 10.2V-18V
Stick Amp/Volt Range:
5A-160A; 20.2V-26.4V
Plasma Amp/Volt Range:
20A-50A; 88V-100V
Start Amps:
DC: 5A-200A
AC: 20A-200A
End Amps:
DC: 5A-200A
AC: 20-200A
Down Slope Time:
0-25 Seconds
Up Slope Time:
0-10 Seconds
Preflow time:
0-10 Seconds
Post Flow Time:
0-25 Seconds
OverCurrent Protection:
Duty Cycle Protection:
Air Pressure OK Safety Indicator:
TIG Pulse Frequency:
.5-250 Hz
TIG Pulse Time On:
TIG Pulse Amp Range:
Stick Arc Force Control:
Yes, 10-100%
Torch Type:
PT/iPT 60
Recommended Cutting Air Pressure:
75 PSI
Recommended Compressor Capacity:
5.0 CFH @ 90 PSI/ 25 Gallon
This unit is not designed or intended for Industrial fabrication or production welding
TIG single pass capability

Steel: 36 ga. - 3/8"
Aluminum: 24 ga. - 1/4"
Stick electrode diameter capability

Plasma Cutting capability* (with dry air, new consumables, proper air pressure etc.)

up to 1/2" daily use @ 15-20 ipm
up to 5/8" clean cut @ 8-12 ipm
up to 3/4" severance cut @ 3-5 ipm
*Quality and capacity of cut depends upon consumable orifice size, standoff height, travel speed, etc.