SuperUltra 206i

200 amp TIG welder with stick and plasma capability
Special Price $721.05 Regular Price $759.00
In stock
SKU
SU206-I
The MOSFET inverter design of the SuperUltra 206i with DC TIG, Stick and Plasma output keeps things simple and streamlined for the budget-minded welding enthusiast. This entry-level welder/plasma cutter multi-process unit is now more reliable than ever with a new digital control system. The SuperUltra 206i is designed to handle the occasional welding and plasma cutting chore that may crop up around the home shop or hobby garage. With up to 200 amps of DC TIG welding power, the unit has enough power to tackle about any small steel or stainless repair that comes its way. Any metal cutting project up to 3/8"-1/2" can be easily sliced through with the built in High Frequency 50 amp plasma cutter. The unit also has enough power in stick mode to weld with welding rods such as 6013, 7014, and 7018 up to 1/8" in diameter.
Write Your Own Review
You're reviewing:SuperUltra 206i
Economical choice for minimal welding/cutting needs
Dual Voltage design allows unit to be used where ever power is present
DC TIG allows fine repairs on Stainless Steel, Chrome Moly and Steel
HF plasma cutting with pilot arc function
Compact MOSFET-based inverter
Excellent for light hobby work
12 ft. 26-Series Everlast TIG Torch with DINSE connector
Stick electrode holder with 10 ft. cable and DINSE connector
AG-60 Plasma torch with 12 ft cable and DINSE connector
Work clamp with 10 ft cable and DINSE connector
Argon Regulator for TIG
Pressure regulator/water trap for Plasma
Economy foot pedal
IGBT Inverter Type:
MOSFET
Voltage/phase:
Dual Voltage 120/240 1 Phase
TIG output type:
DC only
TIG Start Type:
High Frequency Only
Pulse:
No
Plasma Cutter Arc Start Type:
High Frequency
PilotArc:
Yes
OK-to-Cut Indicator/Low Air pressure safety:
No
OCV:
TIG: 70 V
Stick: 70 V
Plasma: 220V
Max Inrush ( I1MAX ) Amps:
@ 110V: 31A
@ 220V: 27A
Maximum Rated (I1EFF ) Input Amps:
@110V: 19A
@220V: 17A
TIG Output Amps/Volts @ Rated Duty Cycle:
120V:
120A/14.8V @ 35% Duty Cycle
93A/13.7V @ 60% Duty Cycle
72A/12/9V @ 100% Duty Cycle
240V:
200A/18V @ 35% Duty Cycle
160A/16.4V @ 60% Duty Cycle
130A/15.2V @ 100% Duty Cycle

Stick Output Amps/Volts @ Rated Duty Cycle:
120V:
120A/24.8V @ 35% Duty Cycle
93A/23.7V @ 60% Duty Cycle
72A/22.9V @ 100% Duty Cycle
240V:
160A/26.4V @ 35% Duty Cycle
130A/25.2V @ 60% Duty Cycle
100A/24V @ 100% Duty Cycle
Plasma Output Amps/Volts @ Rated Duty Cycle:
120V:
27A/90.8V @ 60% Duty Cycle
21A/88.4V @ 100% Duty Cycle
240V:
50A/100V @ 35% Duty Cycle
40A/96V @ 60% Duty Cycle
30A/92V @ 100% Duty Cycle
TIG DC Amp/Volt Range:
120V: 10A-120A, 10.4V-14.8V
240V: 10A-200A, 10.4V-18V
Stick Amp/Volt Range:
120V: 10A-120A, 20.4V-24.8V
240V: 10A-160A, 20.4V-26.4V
Plasma Amp/Volt Range:
120V: 10A-27A, 84V-94V
240V: 10A-50A, 84V-100V
Preflow time:
Fixed
Post Flow Time:
Fixed
OverCurrent Protection:
Yes
Duty Cycle Protection:
Yes
Air Pressure OK Safety Indicator:
No
Stick Arc Force Control:
Auto-Adaptive
Weight: 40 lb
Torch Type:
Everlast AG-60 High Frequency
Recommended Cutting Air Pressure:
55-60 psi
Recommended Compressor Capacity:
4CFM@90 psi/ 20 gallon tank
The SuperUltra 205 is MOSFET based inverter unit, designed as a basic, entry level unit. This unit is not recommended for production welding or fabrication.

Due to the DC only output in TIG mode, this unit is not suited for TIG welding aluminum.

This unit is not recommended for E6010 use.

When operating on a generator, the generator must be rated by the generator manufacturer as "clean power" which is considered less than 5% total harmonic distortion (THD).

For 120V operation on a generator, use a generator with at least 3800 surge watts output.

For 240V operation on a generator, use a generator with at least 6500 watts output.
minimum_maximum
TIG:

Weld steel to a maximum of 5/16" single pass (240V)
Weld steel to a maximum of 3/16" single pass (120V)
Weld steel to a maximum of 1/2" multi-pass(240V)
Weld steel to a maximum of 3/8" multi-pass (120V)
Weld aluminum to a maximum of 1/4" single pass (240V)
Weld to a minimum of .005" Steel
Stick electrode diameter capability:

1/16"-1/8" (3/32 120V)
Plasma Cutting capability* ( with dry air, new consumables, proper air pressure etc.)

Up to 1/4" regular use 15-20 ipm (240V)
Up to 3/8" clean cut @ 8-12 ipm (240V)
Up to 1/2" maximum severance cut (occasional use only) @ 3-5 ipm (240V)
Up to 1/8" regular use 15-20 ipm (120V)
Up to 3/16" clean cut @ 8-12 ipm (120V)
Up to 1/4" maximum severance cut (occasional use only) @ 3-5 ipm (120V)
*Quality and capacity of cut depends upon consumable orifice size, standoff height, travel speed, etc.